Competitive Mechanical Engineering MCQs – Production Technology MCQs Latest
This post is comprising of latest “Production Technology MCQs Latest – Competitive Mechanical Engineering MCQs “. Here you’ll get latest mechanical engineering mcqs for written test, interview with answers. If you want to improve your knowledge regarding mechanical engineering then read these mcqs of Design of Steel Structures.
Latest Mechanical Engineering MCQs
By practicing these MCQs of Mechanical Engineering MCQs – Production Technology Mcqs, an individual for exams performs better than before. This post comprising of mechanical engineering objective questions and answers related to “Production Technology Mcqs“. As wise people believe “Perfect Practice make a Man Perfect”. It is therefore practice these mcqs of mechanical engineering to approach the success. Tab this page to check “Latest Production Technology Mcqs” for the preparation of competitive mcqs, FPSC mcqs, PPSC mcqs, SPSC mcqs, KPPSC mcqs, AJKPSC mcqs, BPSC mcqs, NTS mcqs, PTS mcqs, OTS mcqs, Atomic Energy mcqs, Pak Army mcqs, Pak Navy mcqs, CTS mcqs, ETEA mcqs and others.
Latest Production Technology Mcqs
The most occurred mcqs of Production Technology in past papers. Past papers of Production Technology Mcqs. Past papers of Production Technology Mcqs . Mcqs are the necessary part of any competitive / job related exams. The Mcqs having specific numbers in any written test. It is therefore everyone have to learn / remember the related Production Technology Mcqs. The Important series of Production Technology Mcqs are given below:
The employees provident fund act is applicable to________________?
A. all industries other than small and medium industries
B. all industries
C. volunteers
D. the industries notified by Government
E. all major industries
Which of the following layouts is suited for mass production_________________?
A. fixed position layout
B. product layout
C. process layout
D. plant layout
E. functional layout
Pick up the incorrect statement about advantages of work sampling_________________?
A. permits a fine breakdown of activities and delays
B. no time measuring devices are generally needed
C. calculations are easier, method is economical and less time consuming
D. simultaneous study of many operators may be made by a single observer
E. as operators are not watched for long periods, chances of obtaining misleading results are less
Motion study involves analysis of________________?
A. actions of operator
B. tooling and equipment
C. layout of work place
D. all of the above
E. none of the above
Material handling and plant location is analysed by________________?
A. bin chart
B. Gnatt chart
C. Emerson chart
D. travel chart
E. activity chart
According to MAPI formula, the old machine should be replaced by new one when_____________?
A. CAM < DAM
B. CAM = DAM
C. CAM > DAM
D. there is no such criterion
E. none of the above
Value engineering aims at finding out the________________?
A. resale value of a product
B. depreciation value of a product
C. major function of the item and accomplishing the same at least cost without change in quality
D. break even point when machine re-quires change
E. selling price of an item
The technique of value analysis can be applied to____________________?
A. simple items only
B. complicated items only
C. crash programmer items only
D. cost consciousness items only
E. any item
Standing orders which are statutory are applicable to__________________?
A. only major industries
B. all process industries and thermal power plants
C. all industries
D. only key industries
E. all industries employing more than 100 workers
The appellate authority for an industrial dispute is________________?
A. labour court
B. management
C. high court/supreme court
D. board of directors
E. president
In inventory control, the economic order quantity is the_________________?
A. optimum lot size
B. lot corresponding to break-even point
C. highest level of inventory
D. capability of a plant to produce
E. none of the above
Gnatt charts provide information about_____________?
A. material handling layout
B. production schedule
C. break even point analysis
D. determining selling price
E. value analysis
Gnatt charts are used for_________________?
A. scheduling and routing
B. production schedule
C. forecasting sales
D. linear programming
E. none of the above
Machine Design Mcqs
The wastage of material in the store is taken into account by the following method in the evaluation of the material issued from the store_______________?
A. inflated system
B. current value method
C. primary cost method
D. fixed price method
E. variable price method
Which of the following organisation is preferred in automobile industry________________?
A. line organisation
B. functional organisation
C. staff organisation
D. line and staff organisations
E. scalar organisation
Father of industrial engineering is_________________?
A. Taylor
B. Gnatt
C. Jeck Gilberth
D. Newton
E. none of the above
Queuing theory deals with problems of________________?
A. effective use of machines
B. reducing the waiting time or idle Jajme
C. better utilization of man services
D. material handling
E. none of the above.
In steel plant the most important system for materials handling is_____________________?
A. cranes and hoists
B. conveyors
C. trucks
D. locos
E. none of the above
The most popular type of organisation used for Civil Engineering Constructions is_________________?
A. line organisation
B. functional organisation
C. line and staff organisation
D. effective organisation
E. none of the above
Frederick W. Taylor introduced a system of working known as________________?
A. line and staff organisation
B. line organisation
C. functional organisation
D. effective organisation
E. none of the above
The main disadvantage of line organisation is_________________?
A. top level executives have to do excessive work
B. communication delays occur
C. structure is rigid
D. all of the above
E. none of the above
A low unit cost can be obtained by following____________________?
A. product layout
B. automatic material handling equipment
C. functional layout
D. specialisation of operation
E. minimum travel time plan and com¬pact layout
The most important objective behind plant layout is_____________________?
A. overall simplification, safety of integration
B. maximum travel time in plant
C. economy in space
D. to provide conveniently located shops
E. to avoid any bottlenecks
Travel charts provide__________________?
A. an idea of the flow of materials at various stages
B. a compact estimate of the handling which must be done between various work sections
C. an approximate estimate of the handling which must be done at a particular station
D. the information for changes required in rearranging material handling equipment
E. solution to handling techniques to achieve most optimum results
Process layout is employed for_________________?
A. batch production
B. effective utilization of machines
C. continuous type of product
D. all of the above
E. none of the above
Gnatt chart provides information about the________________?
A. proper utilization of manpower
B. material handling
C. production schedule
D. efficient working of machine
E. all of the above
Basic motion time study gives times for basic motions in ten thousandths of_______________?
A. hour
B. minute
C. second
D. day
E. none of the above
Work sampling observations are taken on the basis of_______________?
A. convenience
B. detailed calculations
C. table of random numbers
D. past experience
E. fixed percentage of daily production
TMU in method time measurement stands for__________________?
A. time movement unit
B. time measurement unit
C. time motion unit
D. technique measurement unit
E. time method unit
Micro motion study is__________________?
A. analysis of a man-work method by using a motion picture camera with a timing device in the field of view
B. study of man and machine conducted simultaneously
C. motion study of a sequence of operations conducted systematically
D. motion study observed on enhanced time intervals
E. scientific, analytically procedure for determining optimum work method
Choose the wrong statement Time study is used to_________________?
A. determine overhead expenses
B. provide a basis for setting piece prices or incentive wages
C. compare alternative methods
D. determine the capability of an operator to handle the number of machines
E. determine standard costs
Scheduling gives information about____________________?
A. when work should start and how much work should be completed during a certain period
B. that how idle time can be minimized
C. when work should complete
D. proper utilization of machines
E. none of the above
Engineering Materials Mcqs
The standard time for a job is_________________?
A. base time + relaxation time
B. total work content
C. total work content + basic time
D. total work content + delay contingency allowance
E. total work content + relaxation time
The allowed time for a job equals standard time plus___________________?
A. policy allowance
B. process allowance
C. interference allowance
D. learning allowance
E. unforeseen allowance
Micromotion study is__________________?
A. analysis of one stage of motion study
B. enlarged view of motion study
C. minute and detailed motion study
D. subdivision of an operation into therbligs and their analysis
E. motion study of small components upto micro-seconds
String diagram is used when__________________?
A. team of workers is working at a place
B. idle time is to be reduced
C. material handling is to be done
D. all of the above
E. none of the above
What does symbol ‘V’ employ in work study________________?
A. inspection
B. operation
C. delay/ temporary Storage
D. permanent storage
E. none of the above
What does symbol ‘O’ imply in work study________________?
A. operation
B. transport
C. inspection
D. delay/temporary storage
E. none of the above
Work study is concerned with_________________?
A. improving present method and finding standard time
B. improving production capability
C. motivation of workers
D. improving production planning and control
E. all of the above
The time required to complete a task is established and a bonus is paid to the worker for every hour he saves from the established time required. This type of incentive plan is known as_________________?
A. Bedaux Plan
B. Rowan Plan
C. Taylor Differential Piece rate system
D. Halsey Premium plan
E. Day work plan
In the Emerson efficiency plan, a worker receives only his daily wage and no bonus is paid till his efficiency reaches__________________?
A. 75%
B. 60%
C. 50%
D. 80%
E. 90%
If a worker gets a daily wage of Rs HA, then according to Rowan plan, his maximum daily earnings can be______________________?
A. 2 HA
B. 1.5 HA
C. 1.33 HA
D. 1.15 HA
E. 2.5 HA
Which one of the following represents a group incentive plan ?
A. Bedaux Plan
B. Halsey Premium Plan
C. Lincoln Plan
D. Rowan Plan
E. Taylor Plan
In order that linear programming techniques provide valid results________________?
A. relations between factors must be linear (negative)
B. relations between factors must be linear (positive)
C. A. or B.
D. only one factor should change at a time, others remaining constant
E. none of the above
The simplex method is the basic method for__________________?
A. operation research
B. value analysis
C. linear programming
D. model analysis
E. none of the above
Fluid Mechanics Mcqs
The time required to complete a job is established and a bonus is paid to the worker based on the exact % of time saved. This type of incentive plan is known as_________________?
A. Dry work Plan
B. Halsey Premium Plan
C. Bedaux Plan
D. Taylor Plan
E. Rowan Plan
String diagram is used_________________?
A. when a group of workers are working at a place
B. for checking the relative values of various layouts
C. where processes require the operator to be moved from one place to another
D. all of the above
E. none of the above
Slack represents the difference between the___________________?
A. normal allowable time and the latest expected time
B. latest allowable time and the earliest expected time
C. proposed allowable time and the earliest expected time
D. latest allowable time and the normal expected time
E. project initiation tune and actual starting time
A big advantage of PERT over Gantt charts is that in the former case_________________?
A. activity times are clear
B. early start and late finish of an activity are clearly marked
C. activities and events are clearly shown
D. critical path can be easily determined
E. inter-relationship among activities is clearly shown
PMTP (predetermined motion time systems) include___________________?
A. MTM (method time measurement)
B. BNTS (basic motion time study)
C. WFS (work factor systems)
D. all of the above
E. none of the above
Which of the following equations is not in conformity with others______________?
A. organisation performance x motivation = profits
B. ability x motivation = performance
C. knowledge x skill = ability
D. attitude x situation = motivation
E. performance x resources
The basic difference between PERT and CPM is that_____________?
A. critical path is determined in PERT only
B. PERT deals with events and CPM with activities
C. costs are considered on CPM only and not in PERT
D. guessed times are used in PERT and evaluated times in CPM
E. PERT is used in workshops and CPM in plants
Queuing theory is used for____________________?
A. traffic congestion studies
B. inventory problems
C. job-shop scheduling
D. all of the above
E. none of the above
Queuing theory is associated with __________________?
A. inspection time
B. sales
C. waiting time
D. production time
E. inventory
Monte Carlo solutions in queuing theory are extremely useful in queuing problems_________________?
A. that can’t be analysed mathematically
B. to verify mathematical results
C. involving multistage queuing
D. all of the above
E. none of the above
A milestone chart_______________________?
A. shows the inter dependences of various jobs
B. points outgoing ahead of schedule of jobs, if any
C. depicts the delay of jobs, if any
D. all of the above
E. none of the above
The first method invented for planning projects was________________?
A. bar chart method
B. critical path method (CPM)
C. milestone chart
D. programme evaluation and review technique (PERT)
E. none of the above
The time of completing a project in network analysis is given by following time of the critical activity meeting at the finalitiode_________________?
A. early finish
B. late start
C. early start
D. late finish
E. none of the above
Emergency rush order can be pushed more effectively in__________________?
A. job production
B. continuous production
C. automatic production
D. intermittent production
E. none of the above
The performance of a specific task in CPM is known as ______________________?
A. event
B. dummy
C. activity
D. contract
E. none of the abov