Structural Design Specifications Mcqs – (Civil Engineering) MCQs Latest For FPSC, PPSC, NTS, KPPSC, SPSC & Other Tests
“ Structural Design Specifications Mcqs “. Tab this page to check “Latest Structural Design Specifications Mcqs “ for the preparation of competitive mcqs, FPSC mcqs, PPSC mcqs, SPSC mcqs, KPPSC mcqs, AJKPSC mcqs, BPSC mcqs, NTS mcqs, PTS mcqs, OTS mcqs, Atomic Energy mcqs, Pak Army mcqs, Pak Navy mcqs, CTS mcqs, ETEA mcqs and others. The most occurred mcqs of Structural Design Specifications in past papers. Past papers of Structural Design Specifications Mcqs. Past papers of Structural Design Specifications Mcqs . Mcqs are the necessary part of any competitive / job related exams. The Structural Design Specifications Mcqs having specific numbers in any written test. It is therefore everyone have to learn / remember the related Structural Design Specifications Mcqs . The Important series of Structural Design Specifications Mcqs are given below:
Removal of props under______________?
A. beams spanning upto 6 m is 14 days
B. slabs spanning upto 4.5 m is 14 days
C. slabs spanning upto 4.5 m is 7 days
D. All the above
The spans of filler joists supporting a slab may be considered approximately equal if the longest span does not exceed the shortest span more than__________________?
A. 10%
B. 5%
C. 15%
D. 25%
All reinforcement should be free from_________________?
A. loose rust
B. paints
C. loose mill scales
D. All the above
The permissible bending stresses Pbet for steel slab bases should not exceed_______________?
A. 1500 kg/cm2
B. 1800 kg/cm2
C. 1650 kg/cm2
D. 1890 kg/cm2
Pick up the correct statement from the following?
A. For high tensile steel, the minimum tensile strength is 58 kg/mm2
B. For steel castings, the minimum tensile strength is 41 kg/mm2 and minimum yield stress is 20.5 kg/mm2
C. For mild steel the minimum tensile strength is 44 kg/mm2 and minimum elongation of 23% on a gauge length of 5.65A
D. All the above
The anchorage value of standard U-type hook of a reinforcing bar of diameter d in tension, is______________?
A. 8d
B. 4 d
C. 12 d
D. 16 d
Pick up the correct statement from the following?
A. For rivets of nominal diameters less than 25 mm, the diameter of the rivet hole is taken as the nominal diameter of the rivet plus 1.5 mm
B. The diameter of the rivet hole is taken as the gross area of the rivet
C. The diameter of a rivet, before driving is taken as the nominal diameter of the rivet
D. All the above
Pick up the correct statement from the following?
A. The distance between centres of two adjacent rivets in line with the direction of stress shall not
B. The minimum pitch of rivets should not be less than 2.5 times the diameter of the rivet hole
C. The distance between the centres of two adjacent rivets in line with the direction of stress shall not exceed 12 t or 203 mm whichever is less in compression members
D. All the above
Pick up the correct statement for the web stiffeners?
A. vertical stiffeners are spaced at a distance not greater than 1.5 d and not less than 0.33 d
B. d is the distance between flange angles or the clear distance between flanges
C. for horizontal stiffeners, d is the clear distance between the horizontal stiffener and the tension flange
D. all the above
Moist sand may contain surface water by mass upto__________________?
A. 5.0%
B. 2.5%
C. 1.25%
D. 7.5%